1. Hoş geldiniz, Akvaryum Portalı ailesine katılım için kendinizi hazır hissediyorsanız üye olun.
    Yardım sayfasından forum kullanım desteği alın.

Düşük ph sorununa çözüm

Başlığı 'Tuzlu Su Kimyası ve Ekipman Portalı' kategorisinde Onurs tarafından 28 Aralık 2015 başlatılmıştır.

  1. Onurs

    Onurs

    Mesajlar:
    2.555
    Yer:
    İstanbul
    İsim:
    Onur Sabuncuoğlu
    reef2reef den alıntıdır.

    A common issue among aquariasts is that their tank has a lower than desired pH. Many tanks commonly dip to a pH of 7.8 or even lower at night. Although, to the best of our knowledge, this isn't low enough to harm the inhabitants of your aquarium, it does slow down the growth of your corals.

    The low pH is generally caused by excess carbon dioxide (CO2) in the system for various reasons. Common causes are the buildup of organics in a system, living in an energy efficient (fairly air-tight) house, and the use of a calcium reactor.

    There are several ways of combating the problem. Many people grow macro algae in a refugium on an opposite light cycle from their main tank. The macro algae uses the CO2 during the light periods to create energy (remember photosynthesis?). Others dose with kalkwasser, which both adds calcium and alkalinity to the system and raises its pH. I was doing both of these things but was still having issues with low pH.

    That's when I read about the use of a CO2 scrubber. What's a CO2 scrubber? Very simply, it's a container that holds soda lime. When you run air through the container, the soda lime binds with the CO2. This is commonly used in scuba diving rebreathers and in air lines for patients under anathesia.

    In aquariums, it is very easy to connect the container to the air intake of your skimmer so that no extra carbon dioxide is going into your system. Most people who run CO2 scrubbers report a 0.2 to 0.3 increase in their average pH.


    Parts/tools needed-
    • pelletized soda lime
    • a clean, clear plastic container with cap
    • drill
    • drill bits
    • super glue
    • silicon
    • airline tubing that fits your skimmer's air intake
    • beer
    • screws (optional)
    • C-clamp (optional)
    • hacksaw (optional)
    How to begin- first you need to source your soda lime. The soda lime needs to be in a pellatized form. The powder form can easily get into your system and it is quickly used up. It is also good to get they type that changes color when it binds with the CO2 so that you know when to change it out. I've heard that some people get theirs from a scuba dive store, but that it is expensive. mdb_talon mentions below that he purchased his from a dive store for around $75 for a 5 gallon bucket. I purchased mine from National Airgas, a welding supply store. They call it Sofnoline, which I think is a typo on Sofnolime, the brand name. Some people have paid around $120 for a 5-gallon bucket. I was quoted $80, but was able to talk them down to $60. It should be enough to last me for a year or two.

    [​IMG]

    If you want to just buy a smaller amount, Eynonreefer sourced a 3 lb bag for $7.50 JOR553 - Soda Lime, 3 lb. bag in Anesthesia Products at Med-Vet International

    Next, you need a container to hold the pellatized soda lime. You can use any clean, clear plastic container that you find around your house. I used an empty Gatorade container.

    [​IMG]

    You need to drill small holes in one end of the container for the air to come in. Make sure that the holes are small enough that the soda lime can't fall through and make sure that there are enough of them so that the air is not overly restricted.

    [​IMG]

    On the other end, drill a hole in the cap large enough so that the airline just fits. Push it in a little way and use superglue to temporarily hold it (superglue dries fast, but doesn't do a good job of adhereing to these plastics). Then, use silicon to seal both sides of the interface between the airline and the cap.

    [​IMG]
    While you are waiting for the silicon to dry, you can decide where you want to put your container. If you have a large enough area under your tank, you might be able to just stand it up anywhere. My cabinet is fairly tight, so I used some screws and cut a plastic C-clamp in half to create a small holder for the container over the cabinet doors.

    [​IMG]

    Once the glue is dry, fill the container with soda lime, put on the top and connect the other side of the airline to your skimmer's air intake.

    [​IMG]

    I connected my CO2 scrubber a few weeks ago and the low point of my pH has gone from 7.8 up to 8.0.

    Before CO2 Scrubber
    [​IMG]

    After CO2 Scrubber
    [​IMG]
    I hope this helps some people out. Please let me know if you have any questions or comments.
     
    nhtkmn bunu beğendi.
  2. gogol

    gogol

    Mesajlar:
    438
    Yer:
    Kartal-İSTANBUL
    İsim:
    gökhan göl
    Peki Onur bu ' soda lime ' denilen maddeyi nerden temin edeceğiz? Scubacılar ve anestezistler dısında bunun nerden satıldıgını bilen var mı?
     
  3. Divin

    Divin

    Mesajlar:
    101
    Yer:
    İstanbul
    İsim:
    Mert Yılmaz
    TLF'nin CDX denen urunu de ayni mantikla calisiyor
     
  4. Onurs

    Onurs

    Mesajlar:
    2.555
    Yer:
    İstanbul
    İsim:
    Onur Sabuncuoğlu
  5. Onurs

    Onurs

    Mesajlar:
    2.555
    Yer:
    İstanbul
    İsim:
    Onur Sabuncuoğlu
    Gökhan sanırım medikalcilerde satılan bir ürün biraz araştırmamız lazım sende anestezi uzmanlarına sorabilirsin bunun bizdeki karşılığını.

    ama sanırım asıl bize lazım olan Baralime denen pellet haldeki malzeme onun tanımı CDX e 1e1 uyuyor demekki cdx baralime denen malzeme.

    @YIKIKTEMO bu konuda daha önce bir çalışma yapmıştı sanki ama forumda yazıyı bulamıyorum @YIKIKTEMO abi o çalışmanın linkini paylaşabilirmisin
     
  6. muradtekin

    muradtekin

    Mesajlar:
    2.105
    Yer:
    Gaziantep
    İsim:
    Murat Tekin
    CDX aldım hala düşük ph (hava çekiş hortumu dışarıda olmasına rağmen) :( sıkı bir şekilde koyunca ps hava çekemiyor.
     
  7. Onurs

    Onurs

    Mesajlar:
    2.555
    Yer:
    İstanbul
    İsim:
    Onur Sabuncuoğlu
    Murat kurduğun düzeneğin videosunu paylaşırmısın ?
    Merak ettim cdx granül değilmi arasından nasıl hava geçmez anlamadım
     
  8. muradtekin

    muradtekin

    Mesajlar:
    2.105
    Yer:
    Gaziantep
    İsim:
    Murat Tekin
    Bu düzeneği bozdum abi ama şişe benzeri bir filtre daha denerim ayrıca resimler deki hosuing girişleri 32 lik boru girişi geniştir yani onu da belirteyim
    [​IMG]
    [​IMG]

    Düzeltme : iç hosuing parçası alttaki kanalların dar olmasından da bu durum olmuş olabilir.


    Sent from my iPhone using Tapatalk
     
    Düzenleme: 28 Aralık 2015
    Courageous ve gogol bunu beğendi.
  9. gogol

    gogol

    Mesajlar:
    438
    Yer:
    Kartal-İSTANBUL
    İsim:
    gökhan göl
    Ben şunu gözlemledim; düşük ph sorununda en önemli faktör ph nın yanlış ölçülmesi. Ölçüm yapan cihazın kaliteli olması ve mutlaka iyi kalibre edilmesi gerek. Ben seneye kullnıyorum,ne yapsam ph yukselmiyordu, ölçüm aparatındaki çipin üstüne küçük bir pod yapışmış, temizlediken sonra ph normale geldi :)
     
    akunaki bunu beğendi.
  10. Onurs

    Onurs

    Mesajlar:
    2.555
    Yer:
    İstanbul
    İsim:
    Onur Sabuncuoğlu
    Murat birinci kabın içinde ne var elyaf mı ?
     
  11. Onurs

    Onurs

    Mesajlar:
    2.555
    Yer:
    İstanbul
    İsim:
    Onur Sabuncuoğlu
    katılırım o konuya seneye içinde ölen böcekler ne yiğitleri telef etti bu güne kadar.
    benim ulns tankda 0.006 amonyak gösterdiği için 15 gün kendime gelemedim ben yapmadığım değişiklik vs.. kalmadı onun yüzünden.
    yeni tanka önümüzdeki sene mutlaka lab grade prob ile bir apex alacağım
     
    gogol, Ontheway ve Courageous bunu beğendi.
  12. muradtekin

    muradtekin

    Mesajlar:
    2.105
    Yer:
    Gaziantep
    İsim:
    Murat Tekin
    Elyaf abi fakat onu çıkartıp yine denedim dediğim gibi iç kısım parçasının altındaki kanalları ro dan hatırlarsınız o kanalların dar olmasından da olabilir. Ben ilk mesajınızdaki şişe benzeri bir filtre ile yapmayı düşünüyorum bakalım ne olacak
     
  13. Onurs

    Onurs

    Mesajlar:
    2.555
    Yer:
    İstanbul
    İsim:
    Onur Sabuncuoğlu
    normalde cdx malzemesi phosban reaktörlere konulara kullanılıyor o reaktöründe alt ızgaraları çok dar bence tabana ızgara üzerine mavi sünger koy ve malzemeyi ondan sonra koy kaba ızgaralar tıkanmamış olur bu sayede
     
    Courageous bunu beğendi.
  14. muradtekin

    muradtekin

    Mesajlar:
    2.105
    Yer:
    Gaziantep
    İsim:
    Murat Tekin
    Haklısın abi dediğin gibi yapayım.
     

Sayfayı Paylaş